enfritkoples

Dynamic Product Line

Fan Powered Systems

Fan Powered Filter Systems

  • Dynamic offers a full line of commercial air cleaning equipment with benefits beyond traditional filtration, such as MERV 15 performance, lower energy and operating costs, and the mitigation of odors and VOCs.

    Dynamic Fan Powered Filter Systems can be configured with:

    • Dynamic Polarized-Media Air Cleaners
    • Dynamic V8® Air Cleaning Systems
    • Dynamic Sterile Sweep® Germicidal UVC Systems
    • Dynamic Activated Carbon Matrix (ACM) Systems
  • For those who are serious about theimportance of Air Filtration and Odor Mitigation

    • A comprehensive, scalable “total” solution for a wide variety of applications.
    • Fast, easy installation.
    • Provides ongoing energy savings and long maintenance cycles.
    • Modular components can be tailored to address specific IAQ needs.
    • 120/240 VAC power.
    • ECM (electronically commutated) motor, for very fine speed control, high efficiency at full speed, and dramatic reduction in power usage at low speeds.
    • Standard 10 speed digital controller for simple airflow adjustment.
    • Airflow capability up to 3,000 CFM (with larger fan/motor).

Continue reading

Dynamic V8-DM (Duct Mounted) for VRF and Fan Coil Systems

Dynamic V8-DM (Duct Mounted) for VRF and Fan Coil Systems

  • The Dynamic V8-DM (Duct Mounted) system utilizes active-field technology to polarize both media fibers and airborne particles. The polarized particles are then drawn to both the fibers of the media and other particles. This process brings about a deep cleaning of the air. The technology behind the Dynamic V8 outperforms any Non-HEPA filters on the market for removing ultrafine particles (UFPs).

Dynamic V8 technology utilizes these basic physical principles and couples them with patented developments in material and composite chemistry and media fibre design. The result is revolutionary performance and a new level of energy and operational savings.
  • The perfect solution for better filtration with VRF units
  • MERV 15 performance without ionizing or Ozone generation
  • VOC reduction and removal of ultrafine particles
  • Holds up to 10 times the dust of deep bed high-capacity cartridge and bag filters
  • Filter change-out intervals measured in years instead of months
  • Service access on upstream side unless specified as downstream when ordering
  • Helps qualify for multiple LEED® credits
  • Helps compliance with ASHRAE Standard 90.1 energy requirements
  • Reduces fan hp, db levels, and helps achieve acoustic criteria targets
  • Can help implement the IAQ Procedure of ASHRAE Standard 62 to possibly reduce outdoor air
  • Limited 5 year warranty includes electronics
  • Tested to meet CSA Standard C22.2 No. 187-M19986 and UL Standard 867
  • Standard module heights of 12” and 18” and depths of 24” or 29.5”. Widths can vary to maximize and simplify media replacement.
  • Can be mounted vertically or horizontally.

Continue reading

Dynamic V8 Quick Reference Guide: AHU Installation

Dynamic V8 Quick Reference Guide: AHU Installation

For Dynamic V8 Air Cleaning System selection and configuration in a typical AHU installation.


Shown above: Four Dynamic V8 Modules with Control Panel


Configurations and Sizes

Air Cleaner Modules mount to vertical posts (provided) and stack in the filter section like Legos. Module to Module seals are made with extrusion strips and seal brackets (provided). Pre-filters are generally not needed.

Module width is chosen to minimize the overall number of Modules and keep them the same width in each AHU.  This simplifies media replacement and ordering.  Each Module is numbered and installed according to the submittal.

Example, if the filter section is 106” wide and 82” tall: the configuration is three 34” wide Module columns across, for a total width of 102”.  Each column is comprised of three 18”H Modules and two 12”H Modules, for a total height of 78”.  Once installed, the Modules are flashed and sealed to the walls of the AHU.  The bottom row will have a 1.625” footer and the top row will have a 1.50” header to facilitate sealing in the AHU.  This 3.125” must be added to the overall combined height of the Modules when configuring.

Mounting Options

Dynamic V8s mount to rectangular vertical posts in the AHU.  These are 1” wide and are attached to the ceiling and floor of the AHU.  Posts are provided and are fabricated to the specifics of the AHU.

Access and Service Space Requirements

For Modules 29.5” Deep:  An additional 24” of space, in direction of airflow, is required for media replacement. This service access can be upstream or downstream of the Air Cleaners.

For Modules 24” Deep:  An additional 18” of space, in direction of airflow, is required for media replacement. This service access can be upstream or downstream of the Air Cleaners.

Access is most often through a mixing box, pre-filter section, or coil access section. Dynamic V8 Media Pads are directional, and the system must be ordered as “downstream access” if needed. If Modules are to be installed through access doors, it is important to make sure the door is wide enough for the Modules, e.g. an 18” Module won’t fit through a 16” door.

Electrical Installation and Requirements

The V8 Modules require 24VAC.  An 18” Module draws 6va @ 24vac and a 12” Module draws 3va @24vac.  The Dynamic Control Panel takes line voltage of 120/208/240/480V single-phase only, and outputs 24vac. Powering Dynamic V8s, for up to a 300,000 cfm AHU, should only require a single 15A circuit. The Control Panel provides Return Indicating lights, necessary breakers, disconnect switch and several differential pressure gauge options. The Control Panel is 16”x12”x6.5” and typically mounts adjacent to the access door of the AHU. Control Panels are available rated for indoor or outdoor use. 

Supply wires run from the Control Panel to the Modules as shown in the submittal. Modules are wired together, one to the next, with the supplied jumpers. Return wires run back from the Air Cleaner column to the Control Panel to show power throughout the column. Door interlock switches to de-energize the Air Cleaners are required and supplied.  These break the 24vac circuit and not the line voltage. While each Dynamic V8 runs at 9kV, it is at very low current and there are no exposed live parts.

In the example above, there are nine 18” Modules and six 12” Modules.  The total electrical draw would be 72va and a 100va Control Panel would be used.  Control Panels are available up to 300va.

General Specifications

Pressure drop: of a typical Dynamic V8 bank @ 500fpm: ~0.28” w.g.
Weight:  18” modules = ~2.5lbs/inch of width;  12” modules = ~1.7lbs/inch of width

Other Configurations

24” Deep modules: these are identical in application to the 29.5” modules and are used when there are space constraints.  They have proportionally higher pressure drop and less dust holding capacity.

V8-SL Side Access modules: these are 24” or 29.5” in depth and have a stacking, self-supporting racking system that allows them to be installed and accessed from the side; for applications with no in-unit service access, such as in a rooftop unit. V8-SL Modules are not available in 46” or 48” widths.

VRF and Fan coil modules; these are essentially V8 Modules with a top and a bottom that become sections of duct and are used with equipment with little or no space for filtration. Module enclosures are also available in insulated and uninsulated versions with options for flat or angle filter racks.

Questions? Please call your Authorized Dynamic Representative or Dynamic Air Quality Solutions at 800-578-7873.

Continue reading

Earthquake Tested

Disaster proofing a facility involves a wide range of preventative measures.  The Dynamic V8 Air Cleaning System has passed rigid Special Seismic Certification requirements from the California Office of Statewide Health Planning and Development (OSHPD) through 12/31/2016.  See the video

alt

Continue reading

Copyright © 2021 Dynamic Air Quality Solutions | W3 Web Design & Hosting